Material comparison
316 vs 416 Stainless Steel for Machined Parts
316 vs 416 stainless steel compared for machined parts: corrosion resistance, machinability, magnetism, heat treatment, and what to state in the RFQ.
Short answer
Choose 316 when corrosion resistance comes first, especially around chlorides, and choose 416 when the part needs easy machining or hardening and will see a mild environment. 316 is an austenitic, molybdenum-bearing grade that cannot be hardened by heat treatment; 416 is a martensitic free-machining grade that is magnetic, can be hardened, and gives up corrosion resistance and weldability for machinability.
Both grades are called stainless, but they solve different problems. 316 is the corrosion-resistant workhorse for marine, chemical, food and medical hardware. 416 is the grade machinists reach for on high-volume turned parts such as shafts, pins, valve trim and fasteners, because sulfur added to the steel breaks chips and keeps tools running. Swapping one for the other changes how the part survives in service, so the choice belongs to the designer and should be written on the drawing.

Applicability
316 vs 416 Stainless Steel for Machined Parts use cases
316 for parts exposed to salt water, chlorides, cleaning chemicals, or sterilization, where pitting resistance matters more than machining speed.
416 for turned and milled parts in mild or indoor environments where machinability, hardness, or wear resistance matters most.
416 for parts that must be magnetic or that are hardened and tempered after machining, such as shafts, pins, and valve components.
Either grade when a buyer is weighing cost against service life and needs the trade-off written into the RFQ before quoting.
RFQ inputs
RFQ inputs and drawing requirements
Grade and form
Name the grade (316, 316L, 416) and the bar or plate specification the stock must meet, and say whether a substitute grade is ever acceptable.
Service environment
Describe the environment the part will see, such as salt spray, cleaning chemicals, or indoor air, so the reviewer can flag a grade that may not survive it.
Heat treatment and hardness
For 416, state whether the part is supplied annealed or hardened and tempered, the hardness range, and whether machining happens before or after hardening.
Passivation and finish
Name the passivation specification if one applies (for example ASTM A967 or AMS 2700); free-machining grades such as 416 need a method suited to them.
Welding and magnetism
Say whether the part is welded or must be non-magnetic, because those two requirements usually rule 416 out.
Constraints
Constraints and quote assumptions
- 416 has noticeably lower corrosion resistance than 316; sulfide inclusions that help machining can become pitting sites in aggressive environments.
- 416 is generally a poor choice for welded parts; 316 or 316L welds far more reliably.
- 316 work-hardens and produces stringy chips, so it machines more slowly than 416 and can need more conservative feeds on small features.
- 316 is essentially non-magnetic when annealed but can become slightly magnetic after heavy cold work; if magnetism matters, state the limit.
- Hardening 416 after machining changes dimensions and surface condition, so finish-machining or grinding allowance must be planned.
Related manufacturing examples
Related manufacturing references

Precision Shaft
Precision Shaft is the kind of turned part often made in 416 for machinability and hardness, or in 316 where corrosion governs; the grade is confirmed per RFQ.
Review reference
Shoulder Pin
Shoulder Pin shows a small turned part where 416 hardening and finish allowance, or 316 corrosion resistance, decides the route.
Review reference
Cross-Drilled Sleeve
Cross-Drilled Sleeve illustrates internal features where 316’s stringy chips and 416’s easy chip breaking change the machining approach.
Review referenceRelated pages
Continue the RFQ review
Stainless steel CNC machining
The wider stainless guide: grades, condition, corrosion context and inspection scope.
Open pageSurface finishes hub
Passivation, electropolishing and other finishes for stainless parts, and when to call them out.
Open pageCNC turning
Shafts, pins, sleeves and other turned parts where the 316 or 416 choice usually comes up.
Open pageFAQ
316 vs 416 Stainless Steel for Machined Parts FAQs
Is 416 stainless steel magnetic?
Yes. 416 is a martensitic stainless steel, so it is magnetic in both the annealed and the hardened condition. 316 is austenitic and essentially non-magnetic when annealed, though cold work can make it slightly magnetic.
Can 416 stainless steel be heat treated?
Yes. 416 can be hardened and tempered to raise hardness and wear resistance. 316 cannot be hardened by heat treatment; it only gains strength through cold work. If hardness matters, the RFQ should give the required range and when hardening happens in the route.
What is the difference between 410 and 416 stainless steel?
416 is essentially 410 with sulfur added to make it free-machining. That makes 416 easier and cheaper to machine, but it lowers corrosion resistance, toughness, and weldability compared with 410.
Is 416 a cheaper substitute for 316?
Only when the environment allows it. 416 often machines faster, which can lower the part price, but it will corrode where 316 would not. Treat a switch from 316 to 416 as a design change that needs the designer’s approval, not as a purchasing substitution.
Material comparison
Put the grade decision on the drawing before the quote.
Send the drawing, the grade or the service environment, any hardness or passivation requirement, and whether the part is welded or must be non-magnetic.
Start stainless RFQ